In order to rapidly attenuate the vibration of the frame and the body and improve the ride comfort and comfort of the car, shock absorbers are generally installed on the vehicle suspension system. At present, the double-acting cylinder shock absorbers are widely used in automobiles.
Shock absorbers are vulnerable parts in the use of automobiles. The shock absorbers work well and will directly affect the smooth running of the car and the life of other parts. Therefore, we should make the shock absorbers always in a good working condition.
The following methods can be used to check whether the shock absorber works well. 1. Make the car stop on roads with poor road conditions for 10km and stop. Touch the damper housing. If it is not hot enough, there is no resistance inside the shock absorber. The device does not work. At this point, you can add appropriate lubricants, and then test, if the shell is hot, the shock absorber internal lack of oil, should add enough oil; otherwise, indicating that the shock absorber failure.
2. Press the bumper firmly and release it. If the car has 2 or 3 jumps, the shock absorber is working well.
3. When the car is moving slowly and braking suddenly, if the car vibrates more violently, it indicates that there is a problem with the shock absorber.
4. Remove the shock absorber to erect it, and clamp the lower end of the connecting ring on the vise, and then pull the damping rod several times. This time, there should be a stable resistance, and the upward resistance should be greater than the downward pressure. Resistance, such as unstable or no resistance, may be due to lack of oil inside the shock absorber or damage to valve parts. Repair or replacement of parts should be performed.
After determining that the shock absorber is defective or has failed, check the shock absorber for signs of oil leakage or old oil leakage.
Oil seal gaskets and gaskets are broken and damaged, and the fuel tank cap nut is loose. It may be the oil seal and the gasket failure. Replace the new seal. If you still can not eliminate the oil spill, you should pull out the shock absorber, if you feel there is a hairpin or different severity, and then further check the piston and cylinder bore is too large, the shock absorber piston rod bent, the piston rod Whether the surface and cylinder are scratched or scratched.
If there is no oil leakage in the shock absorber, check the shock absorber connecting pin, connecting rod, connecting hole, rubber bush, etc. for damage, loosening, cracking or falling off. If the above inspection is normal, the shock absorber should be further decomposed to check whether the clearance between the piston and the cylinder is too large, whether the cylinder is damaged, whether the valve seal is good, and whether the valve flap and the valve seat are tightly fitted and reduced. Whether the extension spring of the shock absorber is too soft or broken, it is repaired or replaced according to the situation.
In addition, shock absorbers may malfunction in actual use. This is mainly due to shock absorbers colliding with leaf springs, frames, or shafts, damage or detachment of rubber pads, and deformation of the shock absorber dust caps. If it is caused by lack of reasons, the cause should be ascertained and repaired.
Cutting Material: Cr12MoV, Heat treatment
Cutting type: Hydraulic / Mechanical controlling cutting
Total motor power: 18.5 KW
Forming Power: 7.5KW Bending Power: 4.0KW
Cutting Power: 4.0KW Conical Power: 3.0 KW
Material of rollers: 45# steel, quenched HRC 58-62
Material of shafts: 45# steel, adjusted
Step of rollers: 13+1
Applicable Span: 5m~28m
The depth of the groove: 175 mm
Operating factor of the panel: 70 %
Thickness of the Panel: 0.8-1.5mm
Working Speed:
Straight Sheet: 15m/minb
Arch Sheet: 13m/min
Seaming: 6m/min
Electric Standard: 380V / 50 HZ / 3 PHASES or according to your requirement
Controlling system: PLC
Large Span Arch Machine, Span Machine, Span Arch Machine
Botou Xianfa Roll Forming Machine Factory , http://www.rollformingmachinecn.com