The material of the medical waste transport vehicle produced by Hubei Chengli Special Purpose Vehicle Co., Ltd. is made of external glass steel, stainless steel plate, ultraviolet sterilization lamp, and spray disinfection device. Double-opening the back door, with a fixed horizontal ring in the compartment and a circular transition in the inside corner. Standard minus 5 degree refrigeration unit. There is no leakage in the seal of the entire vehicle body, ensuring that the medical device does not breed bacteria on the way of transportation.
Chassis configuration: single-row cab, JAC Isuzu States four horsepower diesel engine 120, 7.00 steel tire, air brakes, fifth gear box, factory air conditioning, the rear axle 5 tons, the direction of power.
Standard configuration: box size length × width × height: 4130 × 1810 × 1700 , 12.7 cubic meters , the thickness of the car body is 8 cm. The outer plate is made of special fiberglass for refrigerated trucks, the inner material is stainless steel (reflects sunlight), the middle layer is polyurethane foam insulation material, (fireproof flame retardant insulation) is pressed by a large-scale 10,000-ton press , and the configuration box is all Stainless steel locks, stainless steel corners, stainless steel door frames, ceiling lights and bumpers. Our factory's medical waste transfer vehicle thermal insulation materials use imported grade XPS, water absorption rate ≤ 1, thermal conductivity ≤ 0.028W/mk, compression pressure ≥ 150Kpa, density 30 ~ 45kg/m3, use the world's most advanced fifth-generation fully enclosed Polyurethane plate adhesive structure, carton surface materials are glass steel, stainless steel, aluminum alloy, color steel plate and other materials to choose from, after molding the car body has the advantages of light weight, high thermal insulation coefficient, strong impact resistance, no leakage, etc. Atmosphere, water and acid, alkali, salt and other media have good corrosion resistance and aging resistance. By optimizing the design, the center of mass of the vehicle is reduced and the effective volume is increased. After testing, the comprehensive energy-saving rate of the vehicle and its service life is 1 to 2 times higher than that of a general refrigerated and insulated vehicle.
 Refrigerating unit: adopts Xinxiang Huatai or Xiangyang Hanxue-5 degree refrigeration unit, which has good cold storage effect, fast cooling, and the minimum temperature can reach 0 degrees to minus 5 degrees. It can be adjusted freely according to the demand.
This vehicle is specially designed according to the characteristics of medical waste, and it adopts airtight transportation. The back door is double sealed and uses a labyrinth seal to completely close the carriage so as to prevent the spread of toxic gases from medical waste bacteria. The body of the vehicle has a UV disinfection function. When the UV lamp works normally, it radiates a large amount of ultraviolet rays of 253.7 nm , which is extremely powerful against microorganisms and kills bacteria within 30-45 minutes. The product has closed, impervious, dust-proof properties; antibacterial, fire-retardant, corrosion-resistant, easy cleaning and disinfection functions. According to the “Regulations on Medical Waste Managementâ€, medical waste transfer vehicles must use special vehicles with “medical waste†signs and environmental protection requirements. Sterilization of medical waste transfer vehicles: Anti-virus at low temperature, anti-virus by ultraviolet light and anti-virus by spray of drugs.
Stamping (also known as pressing) is the process of placing flat sheet metal in either blank or coil form into a stamping press where a tool and die surface forms the metal into a net shape. Stamping includes a variety of sheet-metal forming manufacturing processes, such as punching using a machine press or stamping press, blanking, embossing, bending, flanging, and coining.This could be a single stage operation where every stroke of the press produces the desired form on the sheet metal part, or could occur through a series of stages. The process is usually carried out on sheet metal, but can also be used on other materials, such as polystyrene. Progressive dies are commonly feed from a coil of steel, coil reel for unwinding of coil to a straightener to level the coil and then into a feeder which advances the material into the press and die at a predetermined feed length.
Stamping is usually done on cold metal sheet. See Forging for hot metal forming operations.
NINGBO RUICAN MACHINERY COMPANY can offer the Stamping Parts per the drawings or samples.
Stamping Parts
Stamping Parts,Metal Stamping Parts,CNC Stamping Parts,Stamping Bending Welding Parts
Ningbo City Yinzhou Ruican Machinery Co.,Ltd , https://www.kstcasting.com